HP hpe6-a41 Free Practice Questions

NEW QUESTION 1
Refer to the exhibit.

Based on the output shown in this exhibit, which statement is true about the 10.0.0.2 neighbor?

• A. The neighbor rejects communications because it already has its maximum number of neighbors.
• B. The neighbor has mismatched settings and cannot exchange information with this switch.
• C. The neighbor communicates with this switch, but it cannot hold any more routes in its database.
• D. The neighbor communicates with this switch, and they have exchanged all topology information.

Answer: D

NEW QUESTION 2
Which security option for a WLAN provides the best access control security?

• A. MAC authentication with WPA-PSK
• B. WPA2 Enterprise (802.1X)
• C. WPA2 Personal (preshared key)
• D. MAC authentication with WPA2 Enterprise (802.1X) fail-thru

Answer: B

NEW QUESTION 3
Which security benefit does SNMPv3 offer that SNMPv2 does not offer?

• A. SSL encryption
• B. Scopes
• C. Data integrity
• D. RADIUS groups

Answer: C

NEW QUESTION 4
What is a valid setup for a Virtual Switching Framework (VSF) fabric?

• A. one 5406R zl2 switch as commander and one 5412R zl2 switch as a standby member
• B. one 5412R zl2 switch as commander and two 5406R zl2 switches as standby members
• C. one 5406R zl2 switch as commander and two 5412R zl2 switches as standby members
• D. one 5412R zl2 switch as commander and one 5412R zl2 switch as a standby member

Answer: D

NEW QUESTION 5
Two switches are members of a Virtual Switching Framework (VSF) fabric. Which statement correctly describes how the switches handle routing?

• A. Only the commander runs routing protocols and builds the IP routing table, but it programs the standby member to route traffic.
• B. Both members build their own IP routing tables, which they synchroniz
• C. Only static IP routing is supported with VSF.
• D. Only the commander runs routing protocols and builds the IP routing table, and all routed traffic must pass through the commander.
• E. Both members run routing protocols and build their own IP routing tables, and they synchronize thetables over VSF links.

Answer: C

NEW QUESTION 6
Refer to the exhibit.

The network consists of two ArubaOS switches with routing disabled.
How should the network administrator configure the link between Switch A and Switch B to ensure that all hosts can communicate to all the other hosts within their respective VLANs?

• A. tagged for VLAN 20 and tagged for VLAN 30
• B. untagged for VLAN 10 and tagged for VLAN 30
• C. tagged for VLAN 10 and tagged for VLAN 20
• D. untagged for VLAN 10, untagged for VLAN 20, and tagged for VLAN 30

Answer: C

NEW QUESTION 7
Refer to the exhibit.

MSTP is enabled on the switches shown in the exhibit.
Which additional step should the network administrator take to support load sharing of traffic on different switch-to-switch links?

• A. Configure different spanning tree port priorities for different instances on each access layer switch.
• B. Assign different spanning tree port costs to different instances on each access layer switch.
• C. Ensure that half of the switches use config revision 1 and half of the switches use config revision 2.
• D. Create an identical VLAN-to-instance mapping on each switch, in which some VLANs are in each instance.

Answer: A

NEW QUESTION 8
A network administrator needs to configure a link aggregation on an ArubaOS switch.
For which type of link aggregation is the administrator required to enter the lacp command in the interface context?

• A. a distributed LACP link aggregation
• B. a dynamic LACP link aggregation
• C. a static LACP link aggregation
• D. a manual LACP link aggregation

Answer: B

NEW QUESTION 9
Refer to the exhibit.
Exhibit 1.

Exhibit 2.

A network administrator needs to set up DHCP relay in a switched network comprised of ArubaOS switches. Switch A and Switch B have the IP settings in Exhibit 2, and no static or dynamic routes. Switch B is the DCHP server’s default gateway. The administrator correctly configures the IP helper address on Switch A. However, when the DHCP client attempts to acquire an IP address in VLAN 10, the process fails.
What does the administrator need to do to solve this problem?

• A. Configure a static route on Switch A, and enable IP Helper on Switch B.
• B. Configure a static route on Switch A.
• C. Configure a static route on Switch A and Switch B, and enable IP Helper on Switch B.
• D. Configure a static route on Switch A and Switch B.

Answer: D

NEW QUESTION 10
A network administrator creates a local user account and assigns that account to the Level-9 authorization group. The administrator tests the group assignment and is able to successfully log in with the local user credentials. However, the administrator is able to enter all the commands rather than only the commands permitted by the Level-9 group.
How can the administrator resolve this issue?

• A. Set an operator password.
• B. Set the command access level to enable.
• C. Set the command access level to all.
• D. Set command authorization to local.

Answer: D

NEW QUESTION 11
What is one advantage of OSPF over static routing?

• A. OSPF allows ArubaOS switches to use default routes, while static routes cannot use 0.0.0.0/0 as the destination network.
• B. OSPF has a lower default administrative distance than static routing on ArubaOS switches.
• C. OSPF better meets the needs of a complex topology with many redundant routes that static routing.
• D. OSPF permits load sharing traffic over multiple routes, while static routing does not.

Answer: C

NEW QUESTION 12
Which ArubaOS switch feature treats multiple ports as one logical port?

• A. OSPF
• B. STP
• C. VSF
• D. link aggregation

Answer: D

NEW QUESTION 13
A company has an Aruba 5400R switch, switch 1, at the network core of its campus. This switch routes all traffic for the campus and is the RSTP root. The company now wants to add another Aruba 5400R switch to the core in order to enhance resiliency. The company wants to use the option that provides the best Layer 2 and Layer 3 resiliency and also the simplest setup.
What should the administrator do to add the new 5400R switch?

• A. Add the new switch and migrate to MSTP with two instances.
• B. Add the new switch and set up OSPF on all switches.
• C. Add the new switch as a secondary root bridge in RSTP.
• D. Add the new switch as a standby member in a VSF fabric with switch 1.

Answer: C

NEW QUESTION 14
A network administrator wants to download a configuration from an ArubaOS switch. The administrator does not have local access to the switch and wants to copy the configuration in a secure manner that prevents eavesdroppers from reading the configuration. Which two options can the administrator use to copy the configuration?

• A. SFTP and HTTPS
• B. ZModem and SFTP
• C. HTTPS and TFTP
• D. HTTPS and ZModem

Answer: A

NEW QUESTION 15
A network administrator needs to configure a static route. What should the administrator use as the next hop address?

• A. the lowest IP address on the neighboring router in the path towards its destination
• B. the IP address on the local interface that is used to egress traffic towards its destination
• C. the IP address of the default gateway in the destination subnet
• D. the IP address on the connected interface of a neighboring router in the path towards its destination

Answer: D

NEW QUESTION 16
A network administrator is in the context in an ArubaOS switch CLI: Switch (vlan10)#
The administrator wants to leave the configuration context with a single command. Which command should the administrator enter?

• A. logout
• B. quit
• C. exit
• D. end

Answer: B

NEW QUESTION 17
Refer to the exhibit.

This switch currently assigns all VLANs to MSTP instance 0 or the Internal Spanning Tree (IST). Which statement correctly describes interface 21?

• A. The interface is down at Layer 2; it is not available for sending or receiving any traffic.
• B. The interface does not forward or accept data traffic, but it is ready to start forwarding if interface 19 fails.
• C. The interface is an edge port but has received Bridge Protocol Data Units (BPDUs), so it is disabled.
• D. The interface does not support spanning tree: it is possible that it will introduce a loop in the network.

Answer: B

NEW QUESTION 18
Refer to the exhibit.
Exhibit 1.

Exhibit 2.

Assume that Switch-2 is correctly configured for OSPF.
Which additional step must the administrator take to enable Switch-1 to advertise 192.168.2.0/24 to Switch-2?

• A. Set a router ID on Switch-1.
• B. Configure a route to advertise 192.168.2.0/24 on Switch-1.
• C. Add Switch-2’s router ID to Switch-1’s OSPF neighbor list.
• D. Enable OSPF on VLAN 2.

Answer: D

NEW QUESTION 19
A company has a single routing protocol environment.
What is one reason to use OSPF routing instead of static routing?

• A. OSPF allows ArubaOS switches to use default routes, while static routes cannot use 0.0.0.0/0 as the destination network.
• B. OSPF has a lower default administrative distance than static routing on ArubaOS switches.
• C. OSPF reduces the risk of accidentally introducing routing loops, while static routing does not.
• D. OSPF permits load sharing traffic over multiple routes, while static routing does not.

Answer: C

NEW QUESTION 20
An ArubaOS switch operates at factory default settings. A network administrator enters this command:
Switch (config)# password operator plaintext mysecret
How does the switch now control access to the CLI through the console port?

• A. It forces users to enter no username and password operator to gain access to basic mod
• B. Users must then enter password mysecret to reach enable mode.
• C. It forces users to enter username operator and password mysecret to gain access to basic mod
• D. Users can then reach enable mode without authenticating.
• E. It allows users to access basic mode without logging in, but forces them to enter password mysecret to reach enable mode.
• F. It forces users to enter no username and password mysecret to gain access to basic mod
• G. Users can then reach enable mode without authenticating.

Answer: C

NEW QUESTION 21
A network administrator configures MSTP on an ArubaOS switch. The administrator wants to ensure that this switch is always the root for instance 1.
What should the administrator do to accomplish this?

• A. Specify priority 15 for spanning tree instance 1.
• B. Specify spanning tree cost 0 on all switch ports that connect to other switches that use instance 1.
• C. Specify priority 0 for spanning tree instance 1.
• D. Specify spanning tree cost 15 on all switch ports that connect to other switches that use instance 1.

Answer: C

NEW QUESTION 22
Refer to the exhibit.

Based on the exhibit, what is the problem?

• A. An issue causes the spanning tree to converge and re-converge again and again.
• B. Interface 25 on Switch-1 is incorrectly configured as an STP edge port and causes a loop to occur.
• C. Interface 25 on Switch-1 does not support the correct VLANs and prevents the interface from receiving the correct STP role.
• D. Switch-1 and another switch are configured with the same spanning tree priority and cause the root election to occur again and again.

Answer: A

NEW QUESTION 23
Managers log in to an ArubaOS switch with SSH.
What does SSH require to authenticate the switch to the SSH client and set up a secure session?

• A. an SSH authorized user key, managed by the ip ssh public-key commands
• B. a username and password set with the password manager command
• C. an SSH key, managed by the crypto key ss commands.
• D. a self-signed certificate configured with the crypto key commands

Answer: B

NEW QUESTION 24
A network administrator plans two interfaces for a Virtual Switching Framework (VSF) link. Which best practice should the administrator follow?

• A. Configure a low spanning tree cost on the interfaces.
• B. Configure the interfaces as a distributed trunk.
• C. Use interfaces on different modules.
• D. Use copper connections.

Answer: C

NEW QUESTION 25
Refer to the exhibit.

A network administrator installs a new aggregation and access layer in a campus network. All users in this area belong to the same VLAN. The administrator plugs the switches into the network with the factory default configurations.
Which protocol must the administrator configure to prevent broadcast storms?

• A. MSTP
• B. LLDP
• C. OSPF
• D. LACP

Answer: A

NEW QUESTION 26
......